MGH 621Gas hobInstructionbookletGB
10As soon as a liquid starts boiling, turn down theflame so that it will barely keep the liquidsimmering.Use only pans or pots with flat bottom.If you
11Before any maintenance or cleaning can be carried out, youmust DISCONNECT the hob from the electricity supply.The hob is best cleaned whilst it is s
12Something Not Working?If the hob is not working correctly, please carry out the following checksbefore contacting your local Service Force Centre.
13OVERALL DIMENSIONSOVERALL DIMENSIONSOVERALL DIMENSIONSOVERALL DIMENSIONSOVERALL DIMENSIONS Width: 580 mmDepth: 500 mmCUT OUT DIMENSIONSCUT OUT DIMEN
14BURNER RAPID SEMI-RAPID AUXILIARY(large) (medium) (small)POSITION MAX MIN MAX MIN MAX MINNOMINAL THERMAL 3.0 0.75 2.0 0.45 1.0 0.33POWER (kW)NOMINAL
15Important safety requirementsThis hob must be installed in accordance with the Gas Safety (Installation and Use)Regulations (Current Edition) and th
16InstallationIMPORIMPORIMPORIMPORIMPORTTTTTANTANTANTANTANTThis hob must be installed by a competent person to theThis hob must be installed by a comp
17A)A)A)A)A ) End of shaft with nutB)B)B)B)B ) WasherC)C)C)C)C ) ElbowIt is important to install the elbow corrIt is important to install the elbow co
182BBBBBuilding over a kitchen unituilding over a kitchen unituilding over a kitchen unituilding over a kitchen unituilding over a kitchen unitwith do
19Carry out the building in of the hob asfollows:• put the seals supplied with thehob, on the edges of the cut out,taking care that the seals meetwith
2Thank you for selecting our applianceThank you for selecting our applianceThank you for selecting our applianceThank you for selecting our applianceT
20Electrical ConnectionsAny electrical work required to install this hob should becarried out by a qualified electrician or competent person, inaccord
21Wiring diagramA. IGNITOR SWITCHB. IGNITOR UNITPermanent ConnectionIn the case of a permanent connection, it is necessary that you install a doublepo
22Fault FindingPreliminary Electrical Systems CheckPreliminary Electrical Systems CheckPreliminary Electrical Systems CheckPreliminary Electrical Syst
23A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on W (Ohms)x 1 scale and adjust zero if necessary.— Test leads from
24Check gas supply atburnerIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgnition System / Gas IgnitionIgn
25CommissioningWhen the hob has been fully installed it will be necessary to check theminimum flame setting. To do this, follow the procedure below.1)
26Conversion from Natural Gas to LPGIMPORTANTThe replacement/conversion from natural gas to LPG should only beundertaken by a competent person.It is i
35676-2905 11/08 R.A
3ContentsImportant Safety InformationImportant Safety InformationImportant Safety InformationImportant Safety InformationImportant Safety Information.
4Important Safety InformationYYYYYou MUST rou MUST rou MUST rou MUST rou MUST read these waread these waread these waread these waread these warnings
5lack of oxygen.z When using the hob for a long period time, the ventilation should be improved,by opening a window or increasing the extractor speed.
6INSTALLATIONAny gas installation must be carried out by a registeredAny gas installation must be carried out by a registeredAny gas installation must
7Description of the Hob3213541. Auxiliary Burner2. Rapid Burner3. Semi-rapid Burners4. Control knobs5. Electric Ignition Push Button
8Lighting the burnersFor easier lighting, proceed beforeputting a pan on the pan support.Once the hob has been installed, it isimportant to remove an
9Do not keep the control knob pressed for more than 15 seconds.If the burner does not light even after 15 seconds, release thecontrol knob, turn it t
Comments to this Manuals